---===SME_1005_00010_0001.djvu===--- Shop Manual chassis Pub.No.TWSE0721, XXXX 2007 For Vietnam ---===SME_1005_00010_0001.djvu===--- Shop Manual chassis Pub.No.TWSE0721, XXXX 2007 For Vietnam ---===SME_1005_00010_0002.djvu===--- GROUP INDEX GENERAL ............................................. CLUTCH ................................................ MANUAL TRANSMISSION................... PROPELLER SHAFT ............................ FRONT AXLE ........................................ REAR AXLE .......................................... WHEEL AND TIRE ................................ FRONT SUSPENSION .......................... REAR SUSPENSION ............................ BRAKE .................................................. PARKING BRAKE................................. STEERING ............................................ BUMPER AND FRAME......................... CAB MOUNTING AND TILT ................. DOOR .................................................... EXTERIOR ............................................ INTERIOR.............................................. HEATER AND VENTILATION............... FOREWORD This Shop Manual is published for the information and guidance of personnel responsible for maintenance of Mitsubishi Fuso truck, and includes procedures for adjust- ment and maintenance services. We earnestly look forward to seeing that this manual is made full use of in order to perform correct services with no wastage. For more details, please consult your nearest authorized Mitsubishi Fuso dealer or distributors. Kindly note that the specifications and maintenance ser- vice figures are subject to change without prior notice in line with improvement which will be effected from time to time in the future. XXXX 2007 Applicable models FE Shop Manual For V ©2007 Mitsubishi Fuso Truck & Bus Corporation ---===SME_1005_00010_0003.djvu===--- This Shop Manual contains the information classified into the following groups. 1. ENGINE volume 2. CHASSIS volume 3. ELECTRICAL volume Group No. Group subject 11 ENGINE 12 LUBRICATION 13 FUEL AND ENGINE CONTROL 14 COOLING 15 INTAKE AND EXHAUST Group No. Group subject 21 CLUTCH 22 MANUAL TRANSMISSION 25 PROPELLER SHAFT 26 FRONT AXLE 27 REAR AXLE 31 WHEEL AND TIRE 33 FRONT SUSPENSION 34 REAR SUSPENSION 35 BRAKE 36 PARKING BRAKE 37 STEERING 41 BUMPER AND FRAME 42 CAB MOUNTING AND TILT 43 DOOR 51 EXTERIOR 52 INTERIOR 55 HEATER AND VENTILATION Group No. Group subject 54 ELECTRICAL ---===SME_1005_00010_0004.djvu===--- 00-1 GROUP 00 GENERAL VEHICLE MODEL CODING SYSTEM ............................................... 00-2 EQUIPMENT MODEL CODING SYSTEM ......................................... 00-3 POWER TRAIN TABLE ..................................................................... 00-4 HOW TO READ THIS MANUAL ........................................................ 00-6 CHASSIS NUMBER, ENGINE NUMBER AND NAME PLATE ....... 00-10 PRECAUTIONS FOR MAINTENANCE OPERATION ..................... 00-12 JACKING UP THE VEHICLE........................................................... 00-22 TABLE OF STANDARD TIGHTENING TORQUES ......................... 00-24 ---===SME_1005_00010_0005.djvu===--- 00-2 1 Basic vehicle type F Cab-over engine truck 2 Load capacity, drive system E 2tonclassandover,4 2 3 Cab type 7 Standard-width cab 8 Wide cab 4 Vehicle variations, Suspension 3 Rigid axle Light duty vehicle (Payload 1500 to 3000 kg) 4 Rigid axle Light duty vehicle (G.V.M. 6000 to 6900 kg) 5 Rigid axle Light duty vehicle (G.V.M. 7000 kg or more) 5 Engine P 4D34T4, 4D34T5 6 Wheelbase E 3350 mm G 3850 mm 7 Chassis arrangement for use None Standard use 8 Rear tire arrangement, Payload 6 Rear double Payload 3000 kg to 4000 kg 9 Vehicle specification S With turbocharger 10 Steering position L Left-hand drive vehicle 1 7 4 35 2 9 810 6 FE73PE VEHICLE MODEL CODING SYSTEM ---===SME_1005_00010_0006.djvu===--- 00 00-3 Model code indication in this manual Model code indication on name plate Code explanation Engine 4D34T4 4 D 3 4 T 4 Power version number With turbocharger Intra-series sequence of development Sequence of development by series Diesel engine Number of cylinders (4 cylinders) Clutch C3W28 C 3 W 28 Disc outside diameter Facing material (W: Woven) Typical load capacity (tonnage class) of vehicle Initial letter of "clutch" Transmission M025S5 M 025 S 5 Number of forward speeds Meshing (S: Synchromesh) Typical load capacity (tonnage class) of vehicle Initial letter of "transmission" Propeller shaft P2 P 2 Typical load capacity (tonnage class) of vehicle Initial letter of "propeller shaft" Front axle F200T F 200 T Type of vehicle (T: Truck) Typical load capacity (tonnage class) of vehicle Initial letter of "front axle" Rear axle R020T R 02 0 T Type of vehicle (T: Truck) Intra-series sequence of development Typical load capacity (tonnage class) of vehicle Initial letter of "rear axle" Reduction and differential D035H D 03 5 H Tooth form (H: Hypoid gear) Intra-series sequence of development Typical load capacity (tonnage class) of vehicle Initial letter of "differential" in reduction and dif- ferential EQUIPMENT MODEL CODING SYSTEM ---===SME_1005_00010_0007.djvu===--- 00-4 Vehicle model Engine Clutch Transmission Propeller shaft Rear axle Reduction & differ- ential FE73PE6SLDD1 4D34T5 C3W28 M025S5 P2 R020T D2H FE84PE6SLDD1 4D34T5 C3W28 M025S5 P2 R020T D2H FE85PG6SLDD1 4D34T4 C4W30 M035S5 P3 R035T D035H POWER TRAIN TABLE ---===SME_1005_00010_0008.djvu===--- MEMO 00-5 00 ---===SME_1005_00010_0009.djvu===---